Morimoto H670 - Adapter: Matsushita Male to 9006 Female

Write a Review
$37.39
$33.99
(You save $3.40 )
SKU: MORIM-H670
UPC: 840203304914
Stock: 0
Vendor: Premier - CSR
SpecialOrder: True
CarbRejected: False
CouponIsOn: False
StockEta: N/A
ProfitMargin: 10.000
CostOfItem: 17.60
ItemPopularity: 0
MapPrice: 15.00
RetailPrice: 18.00
WarehouseStock: 0
EbayAllowed: False
ShippingGroups: ["Flatrate_Premier"]
EbayPrice: 33.99
ShipperHq: {"shipping-groups":["Premier","FreeShipping","Flatrate_Premier"],"shipping-origins":[],"shipping-dimensional-rules":[]}
IsReturnable: True
EbayPriority: 0

Out of stock

  • screenshot-2024-06-06-013938.png
Morimoto H670 - Adapter: Matsushita Male to 9006 Female

Morimoto H670 - Adapter: Matsushita Male to 9006 Female

$37.39
$33.99
(You save $3.40 )

Morimoto - H670

Dead Ballast: If you've got a ballast out on your Nissan, Infiniti, Acura, or Honda; buying a new OEM replacement certainly is not cheap! Custom Setup: If you're doing a quad retrofit on a vehicle with factory HID headlights, these will allow you to run a splitter and relay harness off the factory ballast wiring without any splicing. No Matter What: We're asking ourselves why we didn't make these sooner! These convenient adapters allow the use of aftermarket parts in place of expensive Original-Equipment ballasts with zero cutting, splicing, or re-wiring involved. Quality: Made with stranded copper wire, fully sealed male and female connections, and protected with tech-flex mesh in between; these adapters should last longer than your original ballasts did! Compatibility: Available to fit the OE-side connector on most modern Nissan, Infiniti's, Acura's, and Hondas that use Panasonic/Matsushita Gen III or IV ballasts, or Mitsubishi Electric Gen II or III Ballasts.

Adapter: Matsushita Male to 9006 Female

Dead Ballast: If you've got a ballast out on your Nissan, Infiniti, Acura, or Honda; buying a new OEM replacement certainly is not cheap! Custom Setup: If you're doing a quad retrofit on a vehicle with factory HID headlights, these will allow you to run a splitter and relay harness off the factory ballast wiring without any splicing. No Matter What: We're asking ourselves why we didn't make these sooner! These convenient adapters allow the use of aftermarket parts in place of expensive Original-Equipment ballasts with zero cutting, splicing, or re-wiring involved. Quality: Made with stranded copper wire, fully sealed male and female connections, and protected with tech-flex mesh in between; these adapters should last longer than your original ballasts did! Compatibility: Available to fit the OE-side connector on most modern Nissan, Infiniti's, Acura's, and Hondas that use Panasonic/Matsushita Gen III or IV ballasts, or Mitsubishi Electric Gen II or III Ballasts.

  • Wiring Adapter: 1x Matsushita Male to 9006 Female Adapter
  • Warranty: 2 Years

Wire Thickness: 14 AWG
Length: Approx. 6in / 150mm
Insulation: Braided TechFlex
Connector 1: OE Matsushita Male
Connector 2: 9006 Female
Input Type: OE Matsushita Male (Same as Matsushita Ballast Input)
Output Type: 9006 Female
Wiring Adapter: 1x Matsushita Male to 9006 Female Adapter
Warranty: 2 Years

Customers Also Viewed